How to Use Rifle Scope in Simple Easy Steps?

A scope helps you in shooting your target accurately. It increases your accuracy by giving you a reticle showing exactly where your gun is targeting long distances.

Using a rifle scope properly is an incredible win and the right path in the shooting. To get the most precise shot in the field, you must learn to use a rifle scope!

Step-by-Step Process of Using a Rifle Scope

Step 1. Determine Your Scope

Determine if your scope features a single or variable power lens. A single lens scope provides one level of magnification, whereas a variable power scope features a ring that allows you to settle between different magnification levels.

You can determine the strength of scope by looking at its model number. Scope model number includes two distinct elements. For instance, model “4×30” Indicates that the scope magnifies four times the target, and the diameter of the scope’s objective lens is 30mm.

You should note it to keep the magnification level to the lowest as higher magnification leads to darker the target as the meager amount of light passes through the lens.

Choose the magnification level, which gives you the most unrestricted view of your destination if you have a variable lens.

Step 2. Mount Your Optical Sight

Assemble your optical sight on top of your rifle to secure it. Sometimes you have to buy rings to support your particular scope. If this happens, please ensure that your device and accessory match perfectly with the scope hardware.

However, most rifles already have pre-drilled mounting grooves. Whatever the case, the following is the first step:

Fit your hardware with the design of your scope.
Add the rifle barrel to the range.
Pull any screws so that the space is intact. Make sure the pressure is even on all screws.
Be careful not to lose sight of your riflescope if you tighten it too much! Always try to find a balance for yourself.

Step 3. Align Your Scope Correctly

Your riflescope’s reticle is essential to show your target direction and position.

Make sure you follow the cross figure on your lens, depending on how your reticles look. It helps in ensuring a correctly fixed target.

Reticles sometimes appear as red dot views you need to fix during the boresighting.

However, to align your rifle reticle:

Loosen the ring assembly or mount.
Rotate the scope until it has positioned the reticle correctly.
Ensure horizontal and vertical lines are crossing right in the middle, forming cross-hairs.

At times, A rifle range can use laser boresighting. Should this be the case, you can follow a similar process.

Step 4. Eye Relief Change

The next step would be to consider eye relief after aligning the reticle location. To do this, adjust the distance from the lens to avoid rifle recoil or impact point.

You usually approach the range with a high magnification power. High magnification power led to minor eye relief and increased eyesore chances.

The matter is, if you take that step, you must be conscious of yourself. After all, it’s all about making constant changes to make yourself comfortable.

Do the following to achieve this:

Put the scope as far as it can while it is still on your hardware.
Slowly move the range to your eye until the entire field is visible. Make sure your vision stays the same and doesn’t get any less blurry.
To ensure eye relief, remember to maintain the range within 1 inch. Adjust the scope as control of potential recalls and impacts of bullets.
Tighten the ring with the same pressure once satisfied.

Step 5. Zeroing In

Adjust the range to zero whenever you are shooting with your rifle scope when the mounting is complete. Zeroing shows that even if the distance and target are changed, the bullet will land near where you aimed.

Shooting has no relation to wind speed or height. Almost every standard rifle is zeroed at hundreds of yards, so double-check your work.

Set up your rifle scope in a static position. This is the most critical step. As a result, ensure that your rifle scope will be in a secure place that will not move an inch.

Pull the trigger, note down the impact point, and carefully adjust the scope with particular care for the reticle and every previous step.
Repeat the process until your rifle is zero.

So, when you are in the shooting field, all of your bullets will directly shoot on your target correctly.

👉 You May Also Like : Learn How To Zero A Rifle Scope

Step 6. Trial the Scope and Make a Perfect Shot

It’s now your turn to go to the woods or the shooting range and strike your target to see how it works.

First adjust your strategy based on the impact of your rounds. When firing shots at the target, be as consistent as possible and judge where they hit. Look at your grouping after firing three to five shots.

Secondly, If you’re shooting consistently, each round should hit the target in roughly the same spot. You’ll need to modify the windage to the right if that location is to the left of your planned target. You can alter your elevation if you’re hitting the target too hard.

Conclusion

A scope aids you in firing swiftly and accurately by making targets more visible. Moreover, It also align the aiming point (reticle or crosshairs) with the target in the same plane of focus.

But, using a scope properly also is a significant. Follow these steps carefully and repeat zeroing in step for aiming more correctly.